Toro timecutter z5020 manual

Control panel 2. Control panel 5. Run 2. Ignition key—run position 6. Start Push the blade control switch to Off to disengage the 3. Ignition key—start position 7. Choke control blades Figure Place the throttle control in the Fast position for best If safety interlock switches are disconnected performance.

Always operate in the full throttle or damaged the machine could operate position. Page Stopping The Machine Adjusting the Height of Cut To turn, release pressure on the motion control lever toward the direction you want to turn Figure Place a foot on the The farther you move the motion control levers in foot assist pedal and apply pressure.

Park the machine on a level surface and disengage the blade control switch. Without the grass deflector, discharge cover, or complete grass catcher assembly mounted 2. Move the motion control levers outward to park in place, you and others are exposed to blade position, stop the engine, remove the key, and wait contact and thrown debris. Page Cutting Speed If enhances decomposition and fertilization. Mow at Correct Intervals Normally, mow every four days.

But remember, grass grows at different rates at different times. Page Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Make sure the motion control levers are locked in the Grease Type: No.

Lift the seat forward and lower it to the Grease floor board. Page Engine Maintenance Engine Maintenance 4. Connect a grease gun to each fitting Figure 20 and Figure Pump grease into the fittings until grease begins to ooze out of the bearings.

Servicing the Air Cleaner 5. Wipe up any excess grease. Service Interval: Before each use or daily—Check the air cleaner for dirty, loose or damaged parts. Page Servicing The Engine Oil carefully; do not use if the sealing surfaces are bent or damaged. Clean the air cleaner base as required and check condition. Install the paper element onto the air cleaner base. Secure with the latch. Close the air cleaner cover door. Park the machine so that the drain side is slightly lower than the opposite side to assure the oil drains completely.

Disengage the blade control switch and move the motion controls outward to the park position. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Disengage the blade control switch, move the motion controls outward to the park position, stop the engine, and remove the key. Before removing the spark plug s , clean the area around the base of the plug to keep dirt and debris out of the engine.

A fire or explosion from gasoline can burn you and Figure 28 others and can damage property. Center electrode insulator 3. G Wash hands after handling. Charging the Battery Figure 29 1. Page Servicing The Fuses Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

Maintain the air pressure in the front and rear tires as G specified. Uneven tire pressure can cause uneven cut. Check the pressure at the valve stem Figure Check the tires when they are cold to get the most accurate pressure reading.

If a blade is damaged or worn, replace it immediately with a genuine Toro replacement 1. Rotate the blades until the ends face forward and blade. For convenient sharpening and replacement, you backward Figure Page Leveling The Mower From Side-To-Side The blades must be replaced if a solid object is hit, if the blade is out of balance, or the blade is bent.

To ensure optimum performance and continued Figure 38 safety conformance of the machine, use genuine Toro 1.

Blade 2. Balancer replacement blades. Using the Height of Cut Lever To adjust the height of cut, pull inward and up on the Stopping the Machine lever and move it to the desired position.

Position the The foot assist pedal can be used with the height of cut seat where you have the best control of the machine lever to help adjust the deck height. Move the bypass levers rearward and then down to lock them in place as shown in Figure 22 to disengage the wheel motors. Repeat this on each side of the machine. Move the motion control levers inward to the neutral position.

Page Operating Tips Mowing Direction Alternate mowing direction to keep the grass standing Without the grass deflector, discharge cover, straight. This also helps disperse clippings which or complete grass catcher assembly mounted enhances decomposition and fertilization. Page 23 File down any nicks and sharpen the blades as necessary.

If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. Page Maintenance Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Make sure the motion control levers are locked in the Grease Type: No.

Lift the seat forward. Grease The following components can be accessed by raising 1. Page Engine Maintenance Engine Maintenance 4. Connect a grease gun to each fitting Figure 24 and Figure Pump grease into the fittings until grease begins to ooze out of the bearings. Servicing the Air Cleaner 5. Wipe up any excess grease. Service Interval: Before each use or daily—Check the air cleaner for dirty, loose or damaged parts.

Park the machine on a level surface, disengage the Every hours—Replace the paper blade control switch, stop the engine, and remove element. Page 28 low, add oil of the proper type up to the full mark. Page Servicing The Spark Plug Install the replacement oil filter to the adapter. Wipe up any excess oil on the frame. Page Cleaning The Blower Housing Cleaning the Blower Housing Fuel System Maintenance To ensure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Annually or every hours of operation more often under extremely dusty, dirty conditions , remove the In certain conditions, gasoline is extremely flammable and highly explosive. Wash hands after handling. Figure 33 1. Page Servicing The Fuses Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

Maintain the air pressure in the front and rear tires as G specified. Uneven tire pressure can cause uneven cut. Check the pressure at the valve stem Figure Check the tires when they are cold to get the most accurate pressure reading. Page Mower Maintenance 4.

Damage wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement Checking for Bent Blades blade. For convenient sharpening and replacement, you may want to keep extra blades on hand. Page Removing The Blades The blades must be replaced if a solid object is hit, if the blade is out of balance, or the blade is bent.

To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. Page Leveling The Mower Deck Leveling the Mower Deck Check to ensure the mower deck is level any time you install the mower or when you see an uneven cut on your lawn. The mower deck must be checked for bent blades prior to leveling; any bent blades must be removed and replaced.

Blades side to side 3. Outside cutting edges 2. Sail area of blade 4. Measure from the tip of the blade to the flat surface here G 5. Measure between the outside cutting edges and the flat surface Figure 46 and Figure Blades front to rear 2. Measure from the tip of the blade to the flat surface here Figure 51 1. Adjusting rod 3.

Lock nut 2. Adjusting block 7. To raise the front of the mower, tighten the adjustment nut. Add oil to the crankcase. Remove the obstruction from the 3. The engine mounting bolts are loose. Tighten the engine mounting bolts. The engine pulley, idler pulley, or blade 2. Tighten the appropriate pulley. Contact an Authorized Service Dealer.

Page 43 Notes Page 44 To locate a dealer damages in connection with the use of the Toro Products convenient to you, refer to the Yellow Pages of your covered by this warranty, including any cost or expense telephone directory look under "Lawn Mowers" or access Page 45 Form No.

Cambio del deflector de hierba PrScticas de operaci6n segura Diagrama de pendientes Page 48 Seguridad EstO alerta, vaya mils despacio y extreme las precauciones en los giros. Mire detrfis y al lado antes de cambiar de direccidn. Mantenga siempre los motores de rueda engranados al bajar por una pendiente. Page Pegatinas De Seguridad E Instrucciones Pegatinas de seguridad e instrucciones Las pegatinas de seguridad e instrucciones estfin a la vista del operador y estfin ubicadas cerca de cualquier zona de peligro potencial.

Sustituya cualquier pegatina que est8 dafiada o que falte. Page 54 Simbolos de la bateria Algunos de estos simbolos, o todos ellos, estan en su bateria Riesgo de exptosi6n Mantenga a otras personas a una distancia prudenciaI de Ia bateria. No fume, mantenga Lleve protecci6n ocular; alejado deI fuego y de Ias los gases exptosivos llamas desnudas. Se puede determinan desde la posici6n normal del operador.

Nota: Si el motor estfi caliente, puede no set necesario usar el estfirter. Page E1 Sistema De Interruptores De Seguridad El sistema de interruptores de SiSntese en el asiento, mueva el mando de control de las cuchillas a desengranado y bloquee las seguridad palancas de control de movimiento en la posici6n de aparcar.

Arranque el motor. Con el motor en marcha, engrane el mando de control de 1as cuchillas y levfintese un poco del asiento; Page Parada De La M Quina Parada de la m quina Para detener la mfiquina, mueva las palancas de control de movimiento a punto muerto y luego hacia fuera, a la posici6n de aparcar, desengrane el mando de control de las cuchillas, asegflrese de que el acelerador estfi en la posici6n Rfipido y gire la llave de contacto Page Colocacidn Del Asiento Colocacibn del asiento El asiento puede moverse hacia adelante y hacia atrfis.

Coloque el asiento en la posicitn que le permita controlar mejor la mfiquina yen la que est8 mils cdmodo. Levante el asiento y aiqoje el pomo de ajuste lo suficiente para poder desplazar el asiento Figura Page Descarga Lateral 3. Localice las palancas de desvfo en la parte trasera de la mSquina, en los lados izquierdo y derecho del bastidor. Page 65 Si una cuchilla estfi desgastada o deteriorada, sustitfiyala que avanza el verano, la velocidad de crecimiento de inmediatamente por una cuchilla nueva genuina Toro.

Si no puede cortar la hierba durante un Page Mantenimiento Mantenimiento Nota: Los lados derecho e izquierdo de la mfiquina se determinan desde la posici6n normal del operador. Engrase las ruedas giratorias delanteras y sus pivotes Asegdrese de que las palancas de control de movimiento Figura Page Mantenimiento Del Motor Mantenimiento del motor No lave el elemento de papel ni utLlice aire a presi6n, porque esto dafiarfi el elemento.

Si el elemento estfi sucio, doblado o dafiado, cfimbielo. Maneje con Mantenimiento del limpiador cuidado los elementos nuevos; no los utilice si la de aire junta de goma estfi dafiada. Page 69 4. La bujfa cumple la normativa sobre coloque el tap6n de vaciado. Apriete el tap6n interferencias de radiofrecuencia RFI. Limpie cualquier exceso Aislante deI electrodo Hueco entre electrodos En ciertas condiciones la gasolina central no a escala extremadamente inflamable y altamente EIectrodo lateral explosiva.

Un incendio o una explosi6n No sobrecargue la bateda. Un enrutado incorrecto de los cablesde la bateria podria dafiar la mfiquina y los cables, Cuando la bateda estO completamente cargada, causandochispas. Una presi6n desigual en los neum,'iticos puede hacer que el corte sea desigual.

Para que el afilado y la sustitucidn sean orientados hacia adelante y hacia atrfis Figura Las cuchillas G de repuesto de otros fabricantes pueden hacer clue se Figura 37 incumplan las normas de seguridad.

Mueva la pahnca de nltura de a la ajuste corte posici6n 3 [76 3 pulg. G Figura Page 78 Ponga la altura de corte en 3 [3 pulg. Para bajar la parte delantera hacia adelante y hacia atrfis Figura Page 80 Baje la palanca de ajuste de la altura de corte a la posici6n mSs baja.

Luego repita el proceso. Page 82 Almacenamiento Haga funcionar el motor para distribuir el combustible con acondicionador por todo el sistema de combustible 5 minutos.

Limpieza y almacenamiento Pare el motor, deje que se enfrfe, y drene el depdsito Desengrane el mando de control de las cuchillas, de combustible;