Casio 120cr manual

You can operate this ECR on a basic level by reading the following sections Initialization Loading Paper Page 4: Getting To Know Your Cash Register Getting to know your cash register Getting to know your cash register The position of the Mode Switch controls the type of operations you can perform on the cash register. In this manual, we will refer to specific keys as noted below to make the operations as easy to understand as possible: Register Mode Check Key Feed Key Plugged in?

Enough Roll Paper? Date and Time is correct? Enough small change in the drawer? While The Store Is Open 1. Issuing latest daily sales total if needed.

Generating report by Mode Switch to X position. After Closing The Store You must initialize 2. Plug the power cord of the cash register into an AC outlet.

Mode Switch to REG slack in the paper. Press the following keys to set the current time. For the Euro only Basic Operation after Basic Programming Note: Whenever an error is generated E01 displayed , the input figures reset to 0. Cash Amount Euro Daily Management Report This section tells you the procedures to use to produce reports of the transaction data stored in the cash register's memory.

Important Remember that when you issue a reset Z report, the data that is reported is cleared from the applicable totalizers. P appears in mode display For Dept. For Dept. P3 appears in mode display For Dept. Round off 1. NXX Program code No. BXX Program code No. Use the printer to print receipts. ZXB Program set code No. Enter tax rate A???? CXN Program set code No. Print tax symbol only for Australia. XX Program Code No. To print receipts, please refer to on page 20 to switch the printer for Receipt or Journal.

OFF Z. Install a new Ink Roll and press it downfirmlybutgentlyuntilitsnaps intoplace. Press the following keys to set the current time. Z o P appears in mode display. Press the following keys to set the current date. You can set only one tax calculation system — either an add-on or an add-in depending on the laws in your area. Press the following keys to set the tax rate. C o P3 appears in mode display. ZXB o Program set code No. XXB o Program set code No. Press the following keys to set the currency exchange rate against the Euro.

You can set some programmable options to suit the Australian GST by the following procedure. If you want to cancel this operation, press o instead of p. You can restrict the registable currency to the Euro only by the following procedure. Note that repeat registration can be used with unit prices up to 6 digits long.

You cannot perform the amount tendered operation using the u key. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Part-1 of this User's Manual can help you make a quick start.

Location Locate the Cash register on a flat, stable surface, away from heaters or areas exposed to direct sunlight, humidity or dust. Cleaning Clean the cash register exterior with a soft cloth which has been moistened with a solution of a mild neutral detergent and water, and wrung out. Be sure that the cloth is thoroughly wrung out to avoid damage to the printer. Never use paint thinner, benzene, or other volatile solvents.

Contents Getting to know your cash register Getting to know your cash register Getting to know your cash register. REG Register This is the position used for registration of normal transactions. RF Refund This is the position used for registration of refunds. CAL Calculator This is the position used for calculator mode.

PGM Programming This is the position used to program the cash register to suit the needs of your store. X Read This is the position used to produce reports of daily sales totals without clearing the totals. Z Reset This is the position used to produce reports of daily sales totals. Department Number Display Anytime you press a department key to register a unit price, the corresponding department number appears here.

Note that only one digit is displayed for the number of repeats. Getting to know your cash register Keyboard! In this manual, we will refer to specific keys as noted below to make the operations as easy to understand as possible: Register Mode!

Plugged in? Enough Roll Paper? Date and Time is correct? Enough small change in the drawer? While The Store Is Open 1. After Closing The Store 1. Resetting report by Mode Switch to Z position. You must initialize 2. Plug the power cord of the cash register into an AC outlet. Load the memory protection batteries. Remove the printer cover. Press down on the oval just behind the printer paper inlet, and slide the battery compartment cover toward the back of the cash register. Slide the memory protection battery compartment cover back into place.

Replace the printer paper and printer cover. Figure 1 2. To Select the Date Format and Monetary Mode You can select the date format and Monetary mode after initialization depending on the requirements in your area. Default Monetary Mode is Add 2. P3 appears in mode display Program set code number Select numbers from lists A and B To end the setting. Monetary Mode Selections Add 0 0. Add 1 0. To load journal paper! To remove journal paper!

Cut off the roll paper. Default printer setting is for Journal. To load receipt paper! Tear off any excess paper. Programming 2. Example: Set tax rate 1 as 5. C o P3 appears in mode display? Press the following keys to preset tax status of departments. Tax status for the Departments are fixed as Non-taxable.